Incandescent Reflector Lamps

THE PRODUCT:

Incandescent reflector lamps (IRLs) are the very common cone-shaped light bulbs most typically used in track lighting and "recessed can" light fixtures (low-cost light fixtures that mount flush with the ceiling such that the socket and bulb are recessed into the ceiling). The cone is lined with a reflective coating to direct the light. PAR lamps are the most common type of IRL; other common IRLs include "blown" PAR (BPAR) lamps, which are designed to be a low-cost substitute for widely used PAR lamps, and "bulged" reflector (BR) lamps. Use of BR lamps has ballooned over the past 15 years as manufacturers have taken advantage of a loophole that exempts them from federal standards.

THE STANDARD:

In December 2007, Congress enacted EISA, which required DOE to extend the coverage of EPAct 1992 IRL standards to some previously exempted lamp types, effective June 2008. In June 2009, DOE issued a final rule amending the 1992 reflector lamp standards, although the most common lamp, a 65-watt BR lamp, and other various lamps at 50 watts and below were not included in the 2009 rule. The federal standard, which took effect in July 2012, set an efficacy level in lumens per watt (lpw) that can be achieved by halogen infrared (HIR) lamps incorporating improved reflectors, coatings, and filaments. Improved HIR technologies will increase average baseline efficacy from about 14 lpw to 19 lpw. As a result, average IRL wattage will drop from about 75W to 55W. According to DOE estimates, the 2009 standards will save up to 2.4 quads over 30 years. Over that same 30-year period, businesses and consumers will save up to $18 billion in net present value savings, and carbon dioxide emissions will be cut by up to 106 million metric tons.

In a 2015 final rule, DOE determined that amended standards for IRLs would not be economically justified. (Note: DOE is required to issue either a proposed revised standard or a determination that no change is warranted no later than six years after the last final rule amending a standard.)

Additional savings will come from extending the scope of the standard to cover exempted lamps. In September 2011, DOE published the framework document for energy conservation standards for certain elliptical reflector (ER), bulged reflector (BR), and small diameter IRLs that were exempted from the 2009 final rule. A final rule, initially expected in 2012, was never published. 

KEY FACTS:

Like other incandescent lamps, HIR lamps utilize a tungsten filament, but the filament in HIR lamps is surrounded by a capsule filled with a halogen gas while the glass is coated with a material that reflects infrared light. Introducing a halogen gas and an infrared coating to an IRL increases the efficacy of the bulb in several ways. By reflecting radiant energy, or heat, back onto the filament, the operating temperature increases, resulting in higher light output from a given wattage. The halogen gas increases the longevity of the filament by introducing a regenerative cycle, where the evaporated tungsten from the heated filament combines with the halogen gas to make a gaseous compound, which allows the tungsten to be re-deposited when the compound comes back into contact with the filament. Improved coatings and advanced reflector designs can further increase HIR lamp efficacy and decrease annual electricity consumption of IRLs.

Fact Sheets

Filings

ASAP Press Releases

Reports

Timeline

Federal Date States
Potential Effective Date of Updated Standard 2017
Updated DOE Standard Due 2014
2nd Federal Standard Effective 2012
Test Procedure - Last Revised - Active Mode 2009
2009 DC Standard Effective *
2009 CT Standard Effective *
2nd Federal Standard Adopted (DOE) 2009
2008 WA Standard Effective
2008 VT Standard Effective
2008 MA Standard Effective
2007 DC Standard Adopted
2007 CT Standard Adopted
2006 VT Standard Adopted
2005 WA Standard Adopted
2005 MA Standard Adopted
2005 OR Standard Adopted
2005 NY Standard Adopted
1st Federal Standard Effective 1995
EPACT Initial Federal Legislation Enacted 1992
1st Federal Standard Adopted (Congress) 1992

* State standard never went into effect due to preemption by federal standard.

States not showing an effective date have an ongoing rulemaking process to determine standards.

Timeline reflects state standards from 2001 to present; federal standards from inception to present.